The Phalanx V2 Midi-Tower builds on Kolink's case line-up with a stylish new dRGB-LED model complete with a tempered glass side panel and a brushed aluminium front with a mesh cut-out. Four 120mm PWM fans with dRGB illumination are pre-installed. These look particularly stylish set against the dark black of the Phalanx V2's stylish interior. A bundled hub allows for control of the fans speed and illumination, either directly via the motherboard or the (also bundled) remote control.
Four pre-installed PWM Dual Ring dRGB Fans and Tempered Glass Side
Equipped with 7 PCI slots, the chassis of the Kolink Phalanx V2 consists of steel and the left side bears an attractive tempered glass window. This is not just attached with screws; it folds out conveniently thanks to two hinges. The lower section is completely covered by a shroud that helps conceal the PSU and any less-than-elegant cabling. The two 3,5- or 2,5 drive bays are also located here. There is also space for a further 2 x 2.5 drives on the rear of the case using the predrilled holes.
To ensure excellent airflow, the case offers four pre-installed 120mm PWM fans with digitally addressable dRGB-LED lighting, as well as mesh strips in the front of the case. Three fans are installed in the front of the case, meaning they are visible through the mesh at the front. One is located in the back. All fans are connected to the included fan hub/RGB controller. The fans feature 8 LEDs on the inner edge and 16 on the outer edge. This enables them to generate multiple eye-catching and impressive effects. Additionally, the dRGB lighting can be controlled using the bundled remote control, the reset switch on the I/O panel, or via the motherboard directly. The top of the case allows for two additional 120 mm- or 140 mm fans. For those who generally prefer larger fans, the case supports the installation of three 140 mm fans at the front in place of 120 mm fans should you prefer.
Ingenious Interior Design
The cleverly placed openings in the motherboard tray enable some exceptionally clean and tidy cable management. If users wish, the front- and top of the case are both capable of holding a radiator up to 280 mm in size. The back of the case naturally also holds a 120 mm radiator if needed. In order to protect the case's interior and your hard-earned components from dust, the case includes magnetic fan filters in the top, bottom and front. This makes them a breeze to remove and clean.
Graphics cards up to 37 cm in length and CPU coolers up to 16 cm tall will fit this case. Power supplies can be up to 24 cm long. The I/O panel is located on the top of the Kolink Phalanx V2 and provides Audio-In/Out, a USB 3.0 port and two USB 2.0 connectors. Also present is a dedicated button to cycle through illumination modes when it is connect to the dRGB hub. (Although it is also possible to connected the hub to the motherboard and either control the illumination via software or the included remote control.)
The hub itself offers ten connectors for 6-pin fans with digitally addressable LED lighting. Moreover, there are two connectors for use with LED strips with 5VDG connections in the shape of a 4-pin connector. Also a bundled adapter enables users to connect the controller to Gigabyte motherboards in addition to motherboards from MSI and Asus.
- Designer case in black for motherboards up to E-ATX
- Tempered glass side panel and front with mesh cut-out
- Four pre-installed digitally addressable 120 mm PWM Dual Ring dRGB fans, 6 possible in total
- I/O Panel with 2x USB 2.0 / 1x USB 3.0, HD Audio In/Out
- Supports three radiators in 120-mm-, 240- and 280 mm formats
- 2x 3.5 or 4x 2.5 storage mounts
- Supports graphics cards up to 37 cm long CPU coolers 16 cm tall
- ARGB motherboard control using Asus, MSI and Asrock motherboards
- Included adapter cable to connect ARGB controller to Gigabyte motherboards